Nautilus MineralsNew Vision - New World - New Resources
Subscribe for Updates

Media Kit

Show printable version of 'Nautilus Outlines High Grade Au - Cu Seabed Sulphi...' in a New Window


Recent Updates

28-Nov-14 - Escrowed funds to be released to Nautilus (more...)
12-Nov-14 - Nautilus Minerals announces Financial Results for Q3 2014 (more...)
06-Nov-14 - Nautilus enters into Vessel Charter (more...)




 May 25, 2006
Nautilus Outlines High Grade Au - Cu Seabed Sulphide Zone.

 
Press Release Number 2006 - 03

Vancouver, BC, May 25, 2006 - Nautilus Minerals Inc. (TSX-V. NUS) ("Nautilus Minerals" or "Nautilus") is pleased to announce that it has received from Placer Dome Oceania Limited ("Placer Dome"), the results of its first drilling and sampling program at the Solwara 1 Prospect. The drilling and sampling program was undertaken by Nautilus' farm-in partner, Placer Dome during January and February of 2006, in water depths of approximately 1,600 meters on the sea floor at the Solwara Project in EL 1196, within the territorial waters of Papua New Guinea.

(For location of tenements including Solwara Project see http://www.nautilusminerals.com/i/pdf/LocationofTenements.pdf )

This work has defined two zones of seabed sulphide outcrop 900m and 400m long each with outcrop widths varying from 80m to 200m. (For surface sample locations of Solwara 1 Prospect see http://www.nautilusminerals.com/i/pdf/SurfaceSampleLocations.pdf). Surface sampling of these zones has provided average metal grades of 15.5 g/t Au, 9.6% Cu, 138 g/t Ag, 5.1% Zn, 0.8% Pb and 199 ppm Mo from 49 samples. The highest grade sample returned 32.7 g/t Au, 23.9% Cu, 92 g/t Ag, 0.2% Zn, 0.08% Pb and 590 ppm Mo. These results compare well to the Placer Dome dredge sampling program completed in 2005, which returned average grades of 15.5 g/t Au, 12.2% Cu, 256 g/t Ag and 4.2% Zn from 39 sulphide samples.



(For full details of February 2006 Solwara 1 Prospect Surface Sampling Summary see
http://www.nautilusminerals.com/i/pdf/Solwara1ProspectSurface.pdf )

Drilling returned significant sulphide intercepts up to 19m below the sea bed, with a best intercept of 11.6m at 9.1 g/t Au, 13.1% Cu, 13.6 g/t Ag and 77.9 ppm Mo, with an average sample recovery of 58% from hole SUZDD 028 which is open at depth. The highly variable and friable nature of the sulphide material presented significant challenges for the ship based drilling system used by Placer Dome and resulted in poor sample recovery (average of 47%).




(For full details of February 2006 Solwara 1 Prospect Drilling Summary see
http://www.nautilusminerals.com/i/pdf/Solwara1ProspectDrilling.pdf )

Nautilus CEO David Heydon comments "Completion of this sampling represents a significant leap forward in our goal to be the leader in seafloor mining. The ROV-deployed sonar and camera program has outlined a significant area of sulphide exposed on the seafloor and sampling of this material has shown it contains high grades of both gold and base metals. Sampling of these zones returned average metal grades of 15.5 g/t Au, 9.6% Cu, 138 g/t Ag, 5.1% Zn, 0.8% Pb and 199 ppm Mo, with the highest grade sample returning an impressive 32.7 g/t Au, 23.9% Cu, 92 g/t Ag, 0.2% Zn, 0.08% Pb and 590 ppm Mo. Nautilus Minerals plans to focus activity on this high grade zone and has commenced baseline environmental studies as the basis for potential permitting for a mining lease.

Considerable sulphide thickness (up to 19m) intercepted in drilling indicates that there is significant depth extent to these systems, particularly when you consider that there is also up to 20m of chimney rising above the sea floor. Twenty eight of the 34 holes intercepted significant mineralization: an impressive strike-rate for the first drilling campaign in a new belt. Many of the holes were terminated in sulphide, when sample could no longer be recovered, and some holes intercepted massive sulphides in areas where there was no surface sulphide exposed, indicating further potential laterally and at depth. We plan to better delineate this potential by deploying further drilling and geophysical techniques.

The cutting tests demonstrated that the friable sulphide material, which lead to the poor drill recovery is readily disaggregated using existing rock cutting technology. This supports our seafloor mining concept.

We are very encouraged with these results from what is the first prospect that we have investigated within our tenement holdings. We have at least a dozen other areas of sulphide mineralization that have been discovered by marine scientists in the last 15 years, within our extensive tenement holdings in PNG. We look forward to exploring these and other areas in future programs."

Surface (Chimney) Zone

Detailed bathymetric mapping using multibeam sonar, has mapped two zones of chimney outcrop totaling 1,300m in strike with an across strike width of 80m to 200m. The chimney zones are readily discernable as areas of extreme topographic variation with individual chimney relief up to 20m. All chimney zones were visually inspected to confirm the presence of sulphide outcrop using a Remote Operated Vehicle (ROV), which was also used for sampling.

The bathymetric map was generated using a Reson 8101 multibeam sonar system mounted on the ROV and operated by the experienced marine survey company Geo Century of Newfoundland, Canada. The sonar system was "flown" at a height of 50m above the seafloor along lines 50m apart, achieving a survey accuracy of better than 1m. The area covered by the survey was 1.6km x 1.1km.

Pieces of sulphide rubble up to 180kg were collected from the seafloor using a manipulator arm mounted on the ROV. Samples were either placed in a sample basket or box on the front of the ROV or held in the claws of the manipulator arms and brought to the surface, where they were then processed on board the ship. Sample selection targeted material that was considered representative of the chimney field. In a number of locations multiple samples were taken and assayed.

Surface samples were of varying shapes and sizes, but most comprised pieces of sulphide rubble. A total of 51 representative sub-samples, each of between 0.5 kg and 2 kg, were taken from these larger samples. Smaller pieces were halved using a diamond saw, and representative slices were taken from larger pieces. The remaining portions of each sample were retained for reference purposes.

Drilling

34 holes were completed for a total of 355 meters.

Coring operations were performed by Seacore Ltd., an England based company, and a recognized expert in deep sea core drilling. Core recoveries in the drilling program were low (averaging 47%) due to the friable and highly variable nature of the sulphide material and the drilling technique, which used a surface vessel to deploy a 70 tonne drill pipe 1,600m to the seabed below. Nautilus is developing ROV-based drilling equipment which should produce improved bit control and better core recovery in future programs.

Many of the holes were terminated in sulphide when sample could no longer be recovered indicating further depth potential. Drill holes were vertical and core diameter was 65mm approximately equivalent to HQ size.

Due to the lower than expected recoveries, drill core was sampled on a "drill run" basis rather than per metre. Thus (for example), for a drill run from 3 to 5m (2m total drilled) with only 40% recovery, the 0.8m of recovered material was considered a single sample representing the interval 3m to 5m, and sub-sampled on that basis. A total of 287 drill core samples were submitted for analysis.

All core sub-samples submitted for analysis were half core, with solid pieces halved longitudinally (parallel to the core axis) using a diamond saw, and loose material halved longitudinally using a spatula. The remaining material has been stored for reference.

(A summary of drill results is provided in Table 2, while a complete list of drill and assay logs will be posted on the Nautilus website, or at http://www.nautilusminerals.com/i/pdf/Solwara1ProspectDrilling.pdf )

Cutting Trial Sample

Approximately 15 tonnes of material was recovered from 13 sites by Placer Dome Technical Services engineers using an "off the shelf" pick cutting head situated on a marinised excavator arm attached to a 200 hp ROV. The ROV was leased from and operated by Canyon Services for Placer Dome's drilling and sampling operation. Samples were delivered to a bin on the ROV through a suction pump driven by the ROV assembly. There were considerable problems with this pump which was not sufficiently powerful, resulting in breakdowns during the cutter trials, and questionable sample recovery, particularly of the more dense material. Samples were hoisted to surface then the bin was emptied into drums on the deck of the ship.

The primary objective of the cutting trial was to test cutter configurations, on a range of rock types. As such the cutting sites were chosen as much for ease of access to varying rock types as they were for their proximity to massive sulphides. Because the sampling material was not the prime selection criteria for the cutting trials, the samples collected, a mix of mound material, chimneys and altered volcanics, are not necessarily representative of the Solwara 1 Prospect's mineralized areas.

In total 13 sites were sampled with 34 drums of material being recovered. Each of the 34 barrels of material recovered during the cutting tests was sub-sampled. Due to the nature of the material, sub-sampling was a simple "spear grab" sample taken from the upper half of each barrel: therefore, the sub-samples might not be representative of the material in each respective bin.

(For cutting test sample sites and drill hole locations see http://www.nautilusminerals.com/i/pdf/CuttingTestSampleSites.pdf. For cutting trial sample summary see http://www.nautilusminerals.com/i/pdf/CuttingTrialSampleSummary.pdf )

Nautilus is the first company to commercially explore the ocean floor for gold and copper seafloor massive sulphide deposits and is positioned to become a world leader in underwater mineral exploration. The Company's main focus for 2006 is the Solwara Project, which is located in the territorial waters of Papua New Guinea in the western Pacific Ocean.

For more information please refer www.nautilusminerals.com or contact:

Investor Relations
Nautilus Minerals Inc. (Vancouver)
Email: investor@nautilusminerals.com
Tel: +1 (778) 785 7591

President & CEO
Mr. David Heydon,
Email:dheydon@nautilusminerals.com
Tel: +1 (778) 785 7591

The TSX Venture Exchange has not reviewed and does not accept responsibility for the adequacy or accuracy of the information contained herein. Certain disclosures in this release, including management's assessment of Nautilus' plans and projects, constitute forward-looking statements that are subject to numerous risks, uncertainties and other factors relating to Nautilus' operation as a mineral exploration company that may cause future results to differ materially from those expressed or implied in such forward-looking statements. Readers are cautioned not to place undue reliance on forward-looking statements. Nautilus expressly disclaims any intention or obligation to update or revise any forward-looking statements whether as a result of new information, future events or otherwise.

Sample Custodianship


All sampling, sample handling and analysis was completed under the supervision of Placer Dome. Sampling was carried out aboard the vessel DP Hunter, whilst at sea. All sub-samples were placed into pre-numbered calico bags. The bagged samples were then subsequently placed in groups of five into larger polyweave bags. The polyweave bags were sealed with security tags, which were then signed by the supervising geologist on site at the time. The bags were then placed into 120 litre polyethylene drums for transport to the laboratory.

Laboratory Analysis

All analyses were carried out by ALS Laboratory Group in Brisbane, Australia. ALS operates quality systems based on international standards ISO/IEC17025:1999 "General requirements for the competence of calibration and testing laboratories" and ISO9001:2000 "Quality Management Systems - Requirements".

QA/QC

External certified geochemical reference materials prepared by Geostats Pty Ltd, of Perth, Western Australia and independently tested, were interspersed at regular intervals between the 372 samples submitted for analysis. These reference materials comprised "standards", with known and statistically tested concentrations of the major base and precious metals, and "blanks", with extremely low concentrations of the major base and precious metals. Standards were submitted approximately every 10th sample. Blanks were placed with a similar frequency, but specifically after a drill core sample that appeared visually to be of higher grade. This frequency resulted in approximately 20% of all samples submitted consisting of standards and blanks. Evaluation of these standards and blanks indicate that the quality of the analyses are within acceptable limits.

Qualified Person

These results have been compiled under the supervision of Michael Johnston VP Corporate Development of Nautilus. Mike is a member of the Australasian Institute of Mining and Metallurgy, has 20 years experience in mining and exploration geology, and is a qualified person as defined under National Instrument 43 - 101. He consents to his name being used in this release.

View News Release in PDF Format:
File: http://www.nautilusminerals.com/i/pdf/2006-05-25_NR.pdf
 100 KB, approx. 20 seconds at 56.6Kbps
 
 

You can view the Next News Releases item: Wed Jun 28, 2006, Nautilus Retains Technip to Undertake Offshore Pre Feed Engineering Study

You can view the Previous News Releases item: Mon May 15, 2006, Management Teams Joins Nautilus

You can return to the main News Releases page, or press the Back button on your browser.